Home About Us Press Stockists Customer Service Request a Brochure Contact Us
 
 
 
 
 
 
 
Please select from the following
 
How much does an electric fire cost to run?
With electricity costing approximately 6.5 pence per kilowatt hour, with the heater full on it will cost around 13 pence per hour. With the flame effect only however the cost is only between 0.5 and 0.9 pence per hour.
 
How big a room will a 2KW heater warm?
This is an almost impossible question to answer, it depends on the number of windows, construction, insulation, double glazing etc. In brief, focal point heating should be supplementary to other heating and not the sole heat source in a room.
 
Which fires will fit my inset fireplace?
There is a British standard sized fireplace, 16€ wide x 22€ high, most inset fireplace are designed to fit this size. Check the overall dimension of the fire and ensure that this fits under the mantel or clear of any other obstructions. Then check the inset dimensions of the fire against that of your fireplace. Many of the Burley models have removable spacers which allow you to alter the depth of the fire, these are shown on the product browser.
 
Can I have a longer cable fitted?
To comply with European standards all products leave the factory with a 2 meter cable with a moulded plug. If a longer cable is needed you will need to find a qualified electrician to fit one, under no circumstances may an extension lead be used.
 
Do I need a fireplace?
No, any of the freestanding fires can simply stand on a hearth, although Burley do produce a range of surrounds which can stand against a wall.
 
Can the fire be used on an extension lead?
It is burley appliances policy not to recommend the use of extension leads with our appliances. We have found in the past that some customers have used inappropriate cable ratings in these leads. We have had examples of 13 amp. Fuses being used in extension lead plugs when the maximum rating of the lead was 5 amps. This practice leads to overheating of the cable and/or
plug and possible fire hazards.

We realise that not all customers who wish to use an extension lead with our appliances would necessarily use an inappropriate lead but in the interests of safety we do not recommend their use at all.

It is important for the safe conduction of electricity that connections are not only electrical sound but are also mechanically sound, loose fitting wiring or plugs into sockets are liable to cause a resistance to current flow and overheating it is not unusual to find that the wiring at the back of a wall socket has over the years become loose, this is due to the heating and cooling of the wiring as current is drawn through it. All current produces heat in a conductor that is why it is important to use the correct size of cable to suit the current being drawn by the appliance.

The above conditions apply equally as well to the socket attached to an extension lead. Extension leads in general tend to have a much harder life than fixed wired wall sockets, it is too easy to pull on the extension lead and after a time the strain on the connections at the plug and/or socket end could lead to the connections becoming loose, this is the situation where overheating occurs.

In the event that the cordset supplied with the appliance is unable to reach the socket outlet which the customer intends to use we recommend that the complete cordset is replaced with an appropriately rated cable and plug. This action should be carried out by a suitably qualified person.
 
What does the thermostat do?
The first thing to understand is that the thermostat operates to control the temperature of the room.It will switch the heater on and off to maintain a constant room temperature.

Turning the thermostat to a high number does not increase the heat coming out of the heater. That
output is constant at two kilowatts, but it will result in the heater running for a longer period, thus
giving a higher temperature in the room.
 
How to set the thermostat.
 

(A) Switch on the fire.

(B) Turn the thermostat to number 10.
(C) When the room is at a level of warmth that you require, then turn the control knob back
  very slowly until you hear a click, and the heater stops.
(D) Leave the thermostat at that number. The heater will then switch on & off to maintain the
  temperature you selected. Please note that number 10 will not give more heat that number 2.
 
 
What are the running costs of the Ambience Stove?
On high the Ambience uses less than four (4) pence worth of gas per hour. In practice, because the Ambience is also fitted with a thermostat, it will automatically turn down when your room reaches the desired temperature, therefore using less gas.
 
Does the Ambience only give radiant heat from the flames?
No, the solid cast stove also radiates heat and, in addition, heated air is discharged through the air outlet grille.
 
Does the room require an air vent?
Yes, if you do not already have one fitted it will be a quick job for your installer to fit a passive air vent when he fits the fire.
 
What if I want to use the Ambience Stove in another room?
Simple, just get a qualified installer to remove it and refit it. You can even take it with you when you move house.
 
Is there a minimum area in which the Ambience may be used?
Yes, any room or area should be at least 40m .
 
 

 

 
 
All rights reserved Burley Fires
Service Engineers | Trade | Privacy Policy | Solar Panels from Navitron | Website Design By UKdynamo